P1077 Code Honda Crv

Author Roy 08 Sep 2023

Sent from my iphone using tapatalk Web my 2006 honda crv had two codes p1077 and p1078. P1077 honda code possible causes faulty intake manifold runner control (imrc) valve imrc valve harness is open or shorted imrc valve circuit poor electrical connection how do i fix code p1077 honda code? Check the possible causes listed above.

2006 Honda Crv P1077 Imrc Stuck Short Youtube

When i'm driving on the open road it stays off until i hit city traffic. I did not notice any loss of power or mpg with the p1077 triggering the mil Engine power is achieved by closing and opening the intake manifold runner control (imrc) valve.

I Installed A Brand New Runner Control And Solonoid.

Web what does the p1077 honda code mean? Web throwing p1077 code. Web 2005 honda crv.

The Imrc Is Designed To Give The Engine The Best Characteristics Over Its Operating Rpm Range By Combining Two Intake Manifolds In One.

I replaced the gasket with the runner control assembly but now i am still getting the p1077 code. Web reply save like ricardowelch · #3 · nov 8, 2019 peninsulacrv said: I have checked the internet for the meaning of this but no luck.

Code P1077 Has Come On.

The code says p1077, stuck in high rpm. The intake position sensor and intake manifold control valve solenoid. Web my honda crv 2004 shows trouble code p1077 high rpm.

Engine Power Is Achieved By Closing And Opening The Intake Manifold Runner Control (Imrc) Valve.

The mechanic is not avalable at the present time and the orange check engine light has come on. The most common cause is the imrc solenoid, however, it could be the intake manifold runner or wiring as well. The imrc system controls the flow of air within the intake manifolds by opening and closing the valves to ensure maximum airflow at.

Do I Get My Technician To Just Serve The Valve Or Replace It.

Several parts had to come off to replace the starter including the intake manifold. Web but i guess i could possibly start/try just the solenoid first? Because i’m quite tempted to 1 continue this thread

Would A Flap Being Stuck Open Make Any Type Of Noise?

When the valve is open, there is high torque a high engine speed. And would you think i should just replace the rotary valve? Learn what intake manifold runner control system malfunction low rpm means, location and how to repair?

The Intake Manifold Code Came On.p1077 $09.

Web repair information for p1077 honda code. Web p1077 1 answer 0 votes answered jan 21, 2017 by anonymous here are the diagnostic procedures Web code p1077 rkeller7966 member 2002 honda crv 2.4l 4 cyl automatic 235,000 miles i have a good idle and all hoses hold vacuum and continuity on all connectors are good but i still get code p1077.

Erased The Code And The Mil Has Been Off.

Web p1077 honda possible causes faulty intake manifold runner control (imrc) valve imrc valve harness is open or shorted imrc valve circuit poor electrical conne. Web 1 level 2 op · 2 days ago i’ve changed the temp sensor. Web the p1077 code is one of two codes that indicates a problem with the intake manifold runner control (imrc).

Or Is It Electrical Issue?

Hi everyone, first time posting here and looking for advice. Web 1 answer 0 votes answered dec 9, 2017 by carguy1 (12.6k points) hi there this code is an issue with the intake manifold runner control system. Just watched a video havent taken anything apart yet.

Web Reply Save Like 1 S Stormrockies · #3 · May 25, 2022 This Is What I Get:

Was a another code i got. The engine runs but the code p1077 returns after it is canceled. I have been getting a cel when driving in town traffic and each time i can turn it off by disconnecting the ground on the battery.

Web About Press Copyright Contact Us Creators Advertise Developers Terms Privacy Policy & Safety How Youtube Works Test New Features Nfl Sunday Ticket Press Copyright.

When the valve is closed, there is high torque at low engine speed. I am about to take the intake manifold off and check the runner control and any thing under the intake manifold. It cost about 150 and took about 10 minutes to install.