P1077 Honda Crv 2002

Author Roy 17 Jul 2023

Web how to fix p1077 intake manifold runner control valve stock in a honda crv (2002) 15 minute smog & repair 25 subscribers subscribe 13 share 1.8k views 5. This is usually a sign that there is a problem with your intake manifold. Answered in 10 minutes by: Engine power is achieved by closing and opening the intake manifold runner control (imrc) valve.

How Do I Correct Engine Light Error Readings Of P1077 And P0661 In A

Engine control module (ecm) issues symptoms associated with p1077 code in honda. Truefan31 discussion starter · mar 22, 2020. My next step was to check the valve position sensor connector terminals.

Remove The Two Screws (A) And The Imrc Position Sensor.

When the valve is closed, there is high torque at low engine speed. Vacuum leaks in the intake manifold; Ask your own honda question p1077 is what my scanner reads.

Web Potential Causes Of The P1077 Honda Crv Code.

Faulty wiring or connectors 6. Web web code p1077 2002 honda crv. Then i went to testing resistance.

Web This Is How You Can Fix The Intake Manifold Runner Control System On Honda Crv And Also Other Honda Models.

Imrc valve actuator malfunction 3. John grether can you please recheck the code. Your vehicle may stall while driving if there is a problem with this because it is not getting enough air into the cylinders to complete the combustion properly.

Had Code P1078 For Intake Runner.

The imrc is designed to give the engine the best characteristics over its operating rpm range by combining two intake manifolds in one. 3274 views 5 replies 3 participants last post by truefan31 , mar 22, 2020 jump to latest. Faulty intake manifold runner control (imrc) valve 2.

Now, Error Code P1077 Pops Up About 8 To 10 Seconds After I Start The Engine.

I am supposed to get 3.2 kohm between terminals nos. Web if you have a code p1077 that means that there is a problem with the intake manifold runner control system. I dont see that one.

Answered In 3 Minutes By:

Had code p1078 for intake runner. When the valve is open, there is high torque a high engine speed. Web code p1077 honda description.

Web Code P1077 2002 Honda Crv.

Replaced intake runner and now it has codes p0505, p1505, and p1078. , honda mechanic steve : I already replaced the imrc solenoid.

1 And 3 With Ignition On, I Was Getting The 5 Volts That Is Needed.

Do i need to replace the whole imrc assembly per the dealership or can i just replace the imrc position sensor? I am about to take the intake manifold off and check the runner control and any thing under the intake manifold. Web p1077 honda possible causes faulty intake manifold runner control (imrc) valve imrc valve harness is open or shorted imrc valve circuit poor electrical connection.

When Testing The Terminals Nos.

Damaged or disconnected vacuum lines 5. See service manual.”any help on what it could be? Web 2005 honda crv 2.4 awd, has code p1077 which i already know is the intake runner and is ordered.

When The Valve Is Open, There Is High Torque A High Engine Speed.

I got the code p1099 and i took the intake manifold off and replaced the valve position sensor because i was not getting the right readings for resistance on the sensor side. Web what does the p1077 honda code mean? Engine power is achieved by closing and opening the intake manifold runner control (imrc) valve.

Check Engine Code“P1077 Manufacturer Specific Dtc.

I had it checked out and i’m told the intake manifold runner control valve needs replaced. Web p1077 on 2004 crv. When the valve is closed, there is high torque at low engine speed.

Web 2002 Honda Crv 2.4L 4 Cyl Automatic 235,000 Miles I Have A Good Idle And All Hoses Hold Vacuum And Continuity On All Connectors Are Good But I Still Get Code P1077.

2985 views 5 replies 3 participants last post by truefan31, mar 23, 2020. Read more john grether shop foreman /servi. Web save 202k views 5 years ago on amazon: